Published

How to Choose LED Bulbs for Bathroom Vanity: Brightness, CRI and Wet-Location Rating

Bathroom lighting is not one problem but several. A vanity needs light on faces and hands, while a shower or tub area needs fittings approved for wet locations and careful glare control; the same source recommends recessing a shower downlight lens at least 1 in. and using more than one recessed light in a shower so the tile walls are washed evenly rather than lit by a single bright point [1].

Start with light output rather than the old bulb's wattage, because the source notes that bulb choice is no longer just about matching the wattage of the old bulb and that colour temperature and CRI now have to be selected for LEDs [1]. Enter the room's dimensions into the Room Lighting (Lux) Calculator, choosing either the room's use or a target lux figure; it returns the total lumens needed using the lumen method, with the illuminance table and its source shown on the page. As a practical extension of your own, treat the mirror area as a task zone rather than averaging it into the whole room, and compare that figure with the light output the bulb manufacturer publishes.

Glare deserves as much attention as raw output. Around a tub, the source's guidance is to aim the lights away from the bather's eyes, keep the aperture small with a smaller trim ring, and recess the light source deeply, so the fitting is not the brightest thing in view [1]. A vanity where you stand close to the lamp has the same problem, which is why a diffused or deeply set lamp is easier to live with than an exposed one.

Colour rendering is the second filter. The source's rule of thumb is to choose light sources with a CRI of 85% or higher, on a scale from 1% to 100% that describes how true or normal colours appear under a particular lamp [1]. At a vanity this matters most with skin tones and makeup, where a low-CRI lamp can make a colour match look wrong under the bathroom light and right everywhere else.

Colour temperature should be chosen deliberately rather than by habit. The source gives a working scale: a burning candle is about 1800 K, 2700 K denotes the warm colour of incandescent lamps, 3000 K to 3500 K produces a bright white without the yellowish tint, cool white fluorescent light sits in the 4100 K to 4500 K range, bulbs marketed as daylight are in the 5600 K to 6000 K range, and noon daylight is about 6000 K; for general residential illumination it puts the acceptable range at 2700 K to 3000 K [1]. Judge the final choice in the room rather than from a specification sheet alone.

Keep one target colour temperature across the whole bathroom. A vanity lamp at one colour temperature and a shower downlight at another will make the same tile and paint look different depending on which light is switched on, so pick a figure in the 2700 K to 3000 K range and repeat it on the other fittings [1]. The source's packaging rule is a useful checkpoint here: colour temperature should be marked clearly so you can confirm the match before buying [1].

Wet-zone suitability is a label to verify at the point of sale, not something to infer from a fixture looking sealed. The source calls for wet-location recessed lights around a tub and for deep recessing of shower lenses, which means the fitting's declared rating has to cover the exact position where it will sit; a vanity light above a basin is a different exposure from a downlight inside a shower [1]. Read the manufacturer's wet-location statement for the fitting and check it against that position before buying.

Placement decisions follow from the same source. If the toilet sits next to the vanity it typically does not need its own lighting, but if it is off in a corner or separated by a wall, a specific light such as a recessed downlight may be necessary, and a separate toilet closet needs good general lighting [1]. Sketch the room and mark which positions are task light, which are general light and which are wet zones before you shop.

Dimming is worth confirming rather than assuming. The source requires that the bulb can be dimmed and that this, along with colour temperature and CRI, is marked clearly on the packaging, and it says that if the packaging does not state these simple characteristics, the bulb should not be bought [1]. As a practical step of your own, check that the bulb and the dimmer you already own are listed as compatible, since a dimmable bulb on the wrong dimmer can behave poorly.

A practical sequence for the vanity: measure the room, run the Room Lighting (Lux) Calculator for a total lumen target, then shortlist bulbs at CRI 85 or higher and a 2700 K to 3000 K colour temperature [1]. For shower and tub positions, confirm wet-location approval and the declared rating for that position, then confirm dimmability, and check the pack prints lumens, colour temperature and CRI. The source's simplest test still applies: if those characteristics are missing from the packaging, leave the bulb on the shelf [1].

Sources and dates checked

  1. Bathroom Lighting with Purpose - Fine Homebuilding (2026-11-23)

This article was created with AI assistance and checked by our automated editorial process.

General information; not a binding quote or individual investment, legal, engineering or medical advice.